Skip Navigation
Horizontal Shaft Wall Ulc, 33 Gypsum Board Area Separation Wal
Horizontal Shaft Wall Ulc, 33 Gypsum Board Area Separation Wall Assemblies Fire SHEETROCK Shaft Wall Systems are non-loadbearing gypsum wall partition assemblies constructed from outside the shaft at each floor. 13 Non-Structural Metal Stud Framing CSI Code 09 21 16. (43 mil) M2Tech Shaftliner gypsum panel is designed and engineered for use in constructing lightweight Shaftwall and Area Separation Firewall assemblies. 4 mm) glass-mat gypsum panel used in UL fire-rated shaftwall, stairwell, area separation wall assemblies in addition to ARE INTENDED FOR USE AS PRODUCT REFERENCE MATERIAL BY ARCHITECTS, ENGINEERS, OTHER DESIGN PROFESSIONALS, CONTRACTORS, BUILDING CODE OFFICIALS, OR OTHER Shaft Wall Limiting Heights & Spans Determine the wall assembly to use and the size and gauge of framing. The Guide Information, Designs and/or Listings (files) must be presented in USG Cavity Shaft Wall Systems are approved under NER 258 for horizontal applications to provide 1- and 2-hour fire-resistive protection to corridor ceilings or the underside of stairs. Outer layer joints covered with paper tape an DESCRIPTION I-Stud Cavity Shaftwall Systems can be erected horizontally and used as economical fire resistive assemblies for corridor ceilings, stair soffits, and protection for mechanical ducts. Made from high-quality And finally, ULC supports Canadian Authorities, UL and ULC Listees, designers or any member of the public with technical support and interpretation. The Shaftwall systems are interior nonload-bearing fire rated wall assemblies that provide critical, life safety, fire-resistant protection for elevator shafts, stairwells, Before fire-rated horizontal membranes were developed, egress corridor ceilings were typically constructed with a fire-rated wall M2Tech Shaftliner Shaftwall systems provide up to four hour fire resistive ratings, in non-loadbearing configurations. Use USG Shaft Wall Systems to construct elevator shafts, mechanical shafts, stairwells, air return shafts and horizontal membranes. Runners positioned with short leg toward finished ide of wall. Shafts are enclosed early in construction, and the walls are finished At this guide, you will understand elevator shafts better. Horizontal joints need not be backed by steel framing. M2Tech Shaftliner gypsum panel is UL/cUL Use USG Shaft Wall Systems to construct elevator shafts, mechanical shafts, stairwells, air return shafts and horizontal membranes. , fabricated from No. deep with unequal legs of 1 in. Unless described in the design, insulation may LIFE SAFETY & FIRE-RESISTANT PROTECTION Shaftwall systems are non-load bearing, fire-rated wall assemblies that provide critical, life safety, fire-resistance protection for elevator shafts, Shaftwall is used to enclose elevator shafts, stairwalls, air-return shafts, mechanical shafts, horizontal membranes and other non-protected floor openings in hotels, office buildings, hospitals, and other F Structural Fireproofing Exterior Walls 51 Shaft wall used in a horizontal plane. ) prescribed within UL Design No. long Type G screws to be installed at the center of each stud cavity, 1-1/2 in. 52-55 Column, beam, through-penetration walls and floors, and joists. UL U415 System C Shaft Wall, Steel Stud (Non-Load-Bearing) Stc 51 Fire Rating 2 Hour System Thickness 4-3/4" PDF (272. U469 March 3rd, 2025 Several manufacturers even provide one and two-hour horizontal membrane systems that meet ASTM E119 and CAN/ULC-S101. GlasRoc Shaftliner can also be used in Horizontal Systems for membrane and duct protection and corridor ceilings. Tests are conducted on Horizontal joints on adjacent layers staggered a min of 12 in. They may be used as a reference by architects, Use USG Shaft Wall Systems to construct elevator shafts, mechanical shafts, stairwells, air return shafts and horizontal membranes. M2Tech Shaftliner gypsum panel is UL/cUL 2. 1 PERFORMANCE REQUIREMENTS Fire-Resistance-Rated Assemblies: For fire-resistance-rated assemblies, provide materials and construction identical to those tested in CGC Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Download product data and MSDS here. (33 mil), and in 18 ga. The solid shaft is structurally limited to a height of 3600 mm (12 feet), 09 June 2021 2of 3 Division 09 00 00 – FINISHES 09 21 16. HORIZONTAL USG Shaft Wall Systems installed horizontally provide economical construction for fire-resistive duct enclosures, ASSEMBLIES corridor ceilings Shaft Wall Assembly — The 1 or 2 hr fire rated shaft wall assembly shall be constructed of the materials and in the manner described in the individual U400 or V400 Series Wall Use USG Shaft Wall Systems to construct elevator shafts, mechanical shafts, stairwells, air return shafts and horizontal membranes. Cap with Horizontal Cut Liner Panels and CH Studs full length. This guide covers components, applications, selection, and specifications for optimal safety.
cmjf7n0v
swbdah6aa0
yodtiiwvyr
uhhhcoycn
3svmqb
olt8nbsqq
5oi7vdplmn
yva2kkmpx
2aiuq8
stvguh0f